不朽的爱情

 找回密码
 立即注册
搜索
热搜: 活动 交友 discuz
查看: 100|回复: 1

Clean a shotgun in six simple steps

[复制链接]

28

主题

28

帖子

162

积分

注册会员

Rank: 2

积分
162
发表于 2021-6-29 10:36:07 | 显示全部楼层 |阅读模式
Clean a shotgun in six simple steps

there are shotgun cleaning kits on  tob outdoors online shop toboutdoors.ca

tob outdoors shop sell Hunting Gear

Stop laughing. The night before yesterday, I was cleaning my shotgun in the hotel, which is one of my favorite places to go hunting or shooting skeet competitions. I think it helps me to deal with guns, hoping to lure me to do more the next day.

The best backyard swing settings, games, and family summer parties

But it wasn't just my strange emotional attachment to my game gun that led me to give it a pre shoot bath. It is also reassuring that by the next morning, there will be no flocs, powder residues or viscous oil in the shooting that day.

shootingTargets

I've developed a very simple system where any hunter or shooter can clean up in flight and on the road. But there's a disclaimer: don't completely dismantle it on the road unless you have to. The possibility of missing springs, damaged parts or incorrect reassembly is too high to be completed the night before the operation.

My rule of thumb is always to shoot a practice session between complete disassembly and cleaning and shooting to make sure everything is OK after reassembly.

Gun Cleaning Kit Canada

Step 1 - partial disassembly

Break down the gun into main parts according to what kind of shotgun you use. For too many deficiencies, I keep the whole action. For automatic devices, I'll take them down until I can clean up any moving parts or areas where gas leakage causes some accumulation. The pump can be stripped all the way, but do not remove any small pieces from the inside of the action.

Step 2 - degreasing

I use an aerosol powder solvent or degreaser designed for guns to clean areas with severe fouling. But I avoid spraying any parts with small springs or debris. Sometimes, spraying aerosol products into a trigger device or action may push the parts out of order or drive the parts where you don't want it to scale.

buy shooting targets

My top priority is the barrel, the chamber (if any), the choke and any area where there is significant metal to metal friction.

Step 3 - wipe the bucket

I don't like hopper to clean the barrel of a rifle, but it's my favorite tool to clean the barrel of a shotgun. Just make sure the snake is clean, be careful the pull rope doesn't catch any small parts, and then you pull it through the barrel.

hunting gear online

Another trick is to throw the rope from the bucket to the ground, stand on the rope, slowly pull up the bucket and pull in the hole.

Step 4 - scrub choke

gun cleaning Pellets toronto

I'm too lazy to soak in the choke. It's too long. Instead, I used a brass brush attached to the handle portion of a three piece cleaning stick. Spray some solvent into the pipe and start scrubbing. It won't be long.

I used an old rifle brush to scrape the dirt off the thread. If the brush is dirty, blow it with a few solvents.

Clean the barrel threads and spray out the fouling as much as possible with the straw and the sprayer. A brush can loosen anything stubborn. I used an old rag to remove as much detergent and debris as I could. I stuffed the rag into the muzzle of the gun and "screwed" it into the thread.

After completion, re install the throttle valve with a small amount of grease to prevent jamming, and finally wipe the hole with a swab.

Step 5 - clean and lubricate the action saving

I'm not very clean in action because getting oil and cleaning solution in some areas will attract powder and dust and may cause problems. I use swabs, rags and brushes to clean the obvious dirt and any place with large moving parts. If shooting the autoloader, now is the time to clean the gas ports around the piston and spring assembly.

Each gun is a bit different and needs different types of lubrication. Some parts are stained with a small amount of grease, and some parts are stained with oil. But if I think I can run it dry without causing damage, I usually do.

Step 6 - point clean and tighten

Finally, the whole gun was visually inspected. Clean if necessary and apply a thin layer of oil to the outer surface. Tighten all screws or hardware and reassemble the gun.

Take a minute to open and close, carry the gun, and "practice the swing" on your imaginary target several times to make sure everything feels right.
回复

使用道具 举报

0

主题

3

帖子

8

积分

新手上路

Rank: 1

积分
8
发表于 2021-7-7 10:15:31 | 显示全部楼层
开奖网My top priority is the barrel,幸运飞艇台湾今彩539 the chamber (if any), the choke and any area where there is significant metal to metal friction.

Step 3 - wipe the bucket
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

Archiver|手机版|小黑屋|不朽的爱情

GMT+8, 2021-9-20 08:04 , Processed in 0.009971 second(s), 18 queries .

Powered by Discuz! X3.4

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表